SS Buildcare

• For sealing fine “hairline” cracks in concrete structures. 
• For waterproofing of concrete water tanks, pools etc. 
• For exterior waterproofing of basement walls in new buildings. 
• For all kinds of damp proofing and waterproofing in concrete, mortar, rendering, brickwork and block work. 
• For sealing internal basement and cellar walls against dampness. 
• For Water proofing of Roof Gardens. 

• Excellent adhesion to sound and prepared surfaces. 
• Pre-measured packs – need only mixing. 
• Easy to apply by brush. 
• Excellent barrier coating for CO2 , acid gases and chloride ions. 
• Non-toxic suitable for contact with drinking water. 
• Non-Corrosive to steel or iron, noninflammable. 

DESCRIPTION

NEOPROOF RC 200is a specially designed single part, pollution free liquid waterproofing membrane coating based on special synthetic resin.Its excellent flexibility & thixotropic nature makes it ideal for use on both horizontal & vertical surfaces. It offers superior UV resistance and Solar reflectivity

APPLICATION ARE
SURFACE PREPARATION

Surface should be clean free of dirt, gravel, dust and oil. Concrete and cementitious substrate are to be well compacted and at least 28 days old, with toweled finish. Wood panels or metal sheeting should be solidly fixed and cleaned. 

METHOD OF USE

Prime the prepared surface with NEOPROOF RC 200 diluted in the ratio of 1:2. Post drying of primer, apply 1st & succeeding coats. Apply by brushes, squeegees, rollers or airless spray equipment. Allow full curing of each coat (approx 8 – 10 hours) before applying next coat. The product is water dilutable upto 15-25% for 1st coat & 10 – 15 % for 2nd coat. Ensure complete curing (approx 48 -72 hours) before laying thermal insulation & mechanical protection.

WATERPROOFING CONVENTIONAL ROOFS

Asphalt surfaces: Old asphalt surfaces and asphalt roofing felt after cleaning must be first primed. This would strengthen the weathered surfaces. Blisters in asphalt roofing felt must be cut open cross wise, dried and bonded with suitable adhesive. Terrazzo Tile Roofs: Damaged or washed-out joints should be cleaned, repaired or re-grouted and then primed. Flat roofs with zero pitch: Flat roofs without pitch are roof surfaces where puddles may develop and pose special problems. Puddles after curing cannot be rectified resulting in redoing the entire waterproofing. Hence dry weather condition is must to help satisfactory curing and puddle free coating. Metal Roofs: In case of Iron or galvanized iron: remove loose paint with a wire brush. De-rust corroded areas and prime with suitable metal primers. In case of Zinc or aluminum: remove loose paint with a wire brush. Remove corrosion if present and prime with solvent primer. Thoroughly remove moss and mildew with wire brush; subsequently clean the surface with a broom. Concrete Roofs: After cleaning the roof surfaces, prime the surface followed by multiple coats 

COVERAGE

Approximate coverage is around 25-30 sq. ft per kg per coat. 2 coats of application should generally return DFT of approx 200-300 microns. For higher DFT use additional coats.

STORAGE & SHELF LIFE

Shelf life is 12 months in unopened container. Store away from sunlight and preferably below 30oC.

HEALTH & SAFETY

Exercise caution and use protective clothing such as gloves and goggles. Inhalation of vapor or mist should be avoided. If inhaled symptoms include coughing, wheezing, laryngitis, and shortness of breath, headache, nausea, and vomiting. Immediately shift victim to fresh air & if need be start artificial respiration. Give oxygen if breathing is labored & call emergency medical help. In case of eye contact flush with water for 15 minutes and call for medical help. If swallowed will cause nausea, vomiting, and loss of consciousness. Do not induce vomiting rather call for medical help. If contact with skin flush with water/soap & water until all traces are removed. Seek medical attention if required. Asphalt roof surfaces to be coated.